Customer Support 7 days a week
Shop for Parts
Get Repair Help
Welcome Guest! To enable all features please
Appliance Repair Help
Whirlpool/Kenmore dishwasher impeller replacement
Post a reply
Post a reply
Maximum number of characters in each post is: 32767
[quote=simonboyce;189287][QUOTE=richappy;189182]Sorry for the delay, you pound on the impeller near the 1/4 inch screw, that's where it is rusted to the shaft. Also, there is a flat on the motor shaft that you can hold with an adjustable wrench while you carefully remove the screw. I use penetrating oil on it and work it back and forth till it get loose.[/QUOTE] Thanks Richappy. Bottom line, there's no way to disassemble the pump from the motor without destroying that plastic impeller disk thing?[/quote]
[YOUTUBE]Put YouTube URL in here[/YOUTUBE]
[PART]AP Part Number[/PART]
[HIDE-THANKS=x]The tag hides content from people who have below then X thanks received.[/HIDE-THANKS]
[HIDE-REPLY-THANKS]The tag hides content from people until they either reply in the same thread or press the thank you button for the post.[/HIDE-REPLY-THANKS]
[HIDE-REPLY]The tag hides content from people until they replied in the same thread.[/HIDE-REPLY]
[GROUP-HIDE]Hide the Content from Guests, or other Roles if defined.[/GROUP-HIDE]
[dailymotion]Enter Dailymotion Url (http://www.dailymotion.com/video/xxxx)[/dailymotion]
[HIDE-POSTS=x]The tag hides content from people who have below then X posts.[/HIDE-POSTS]
[GOOGLEMAPS]Enter Google Maps Url[/GOOGLEMAPS]
[ALBUMIMG]Enter a Album Image Number[/ALBUMIMG]
[ATTACH]Enter a Attachment ID[/ATTACH]
[SPOILER]Put Spoiler Text in here[/SPOILER]
[HIDE]This tag hides content from people until they press the thank you button for the post.[/HIDE]
[USERLINK]Put User Name Here[/USERLINK]
[TWITTER]Enter the Status ID of the Tweet you want to embed[/TWITTER]
Enter The Letters From The Security Image:
Last 10 Posts (In reverse order)
Tuesday, December 24, 2019 3:59:40 AM(UTC)
I have been getting a special nut busting solution on it for three 2 days now so that will probably help. Take a sharp wooden chisel and gently pound on the top edge of the impeller near the screw. Crack it away from the shaft , then apply sharp oil to the screw.
Wednesday, April 24, 2019 11:02:30 PM(UTC)
You can once try ... Moved to Dishwasher repair section and made it a "sticky".You can help from near by appliance professional.
appliances repair service
Small appliance repair
Friday, March 15, 2019 2:20:58 AM(UTC)
Here is good
for your problem
Tuesday, March 12, 2019 8:25:51 AM(UTC)
Care Appliance Repair
Call me and we'll figure out this issue.
Friday, February 8, 2019 9:38:22 PM(UTC)
I recommed to use GoTech Appliance Repairs for fast and high-quality assistance. I used their services few times and this is really a reliable assistant in the repair of household appliances,
Wednesday, October 3, 2018 5:50:37 AM(UTC)
thank you so much
Saturday, September 29, 2018 5:22:01 AM(UTC)
Thank you for the helpful information you provided
Monday, May 28, 2018 4:27:00 PM(UTC)
The center screw on my 18-year-old unit was very tight. I tried an adjustable wrench, an open end wrench, and a box-end wrench, but could not hold the top impeller well enough to loosen the screw.
I instead, used a 25mm socket (preferably a 6-point, but a 12-point worked) held in a pair of Vice Grips to hold the impeller. I then used a 1/4" socket in a 1/4"-drive ratchet through the 1/2" drive opening of the 25mm socket to remove the screw.
See photograph, attached.
The screw was extremely tight, but it did not break, and was not corroded when finally removed.
I needed to replace the filter and clean out the thousands of pieces after a tempered drinking glass shattered inside the dishwasher.
Saturday, May 17, 2014 1:26:21 PM(UTC)
I'd suggest against breaking off the impeller.
This bolt does thread in the normal way (righty tighty) so if it's seized instead slightly tighten it first to break it loose (but not too hard so as to crush the rubber gasket under the bolt head), then unscrew it to the left (counter clockwise). Use a 1/4" socket with an extension to a socket wrench. The plastic "nut" on the impeller is 1". Didn't have a 1" box wrench so I used an adjustable. No problem. Pull the impeller up and out of the way.
Next use that same torx screwdriver you used to get to the impeller to remove the four bolts that are now exposed. Gently pull away the assembly. Voila, there's all the junk that's gotten in there. Check the metal mesh on the removed assembly for bits of glass that might be stuck in the mesh to keep them from getting into your motor later.
Monday, March 3, 2014 5:31:45 AM(UTC)
hi guys, after replacing this part kit, my dishwasher is leaking, help ?
Powered by YAF.NET
YAF.NET © 2003-2022, Yet Another Forum.NET