Post a reply - Appliance Repair Forum - Free Service from Appliance Parts Pros

Welcome Guest! To enable all features please Login or Register.

Notification

Error

Post a reply

From:

Message:

Maximum number of characters in each post is: 32767

Font Color Font Size

[quote=denman;775767]Here are your parts
[url=http://www.appliancepartspros.com/partsearch/modelsearch.aspx?model=fef366cce]Parts for Frigidaire FEF366CCE Range - AppliancePartsPros.com[/url]

Here is a better copy of your wiring diagram.
[url]http://manuals.frigidaire.com/prodinfo_pdf/Springfield/316255311.pdf[/url]

Do the oven light and the surface indicator lights work.
If not then you may have a power problem (no neutral).
Try flipping the breaker off/on slowly a couple times. Sometimes you can loose half the line without actually tripping the breaker.
Check the voltage at the plug
L1 to L2 should be 240 volts
L1 to Neutral and L2 to Neutral, both should be 120 volts.
If OK
Unplug the unit and check the wires at the terminal strip in the machine to make sure none are loose or burned out
If OK
Check the power at the terminal strip.
Do this with the heater off and on.
Be careful as 240 volts is lethal !!!

If the lights work then probably the control board (Item 20 in Backguard Parts) is shot. You will also probably need a new overlay (Item 20A), the old one may get messed up trying to remove it.

I would check all the wires going to the control board especially L1 and Neutral.
You cold also check that the board is getting power but this can be a pain to do due to the limited space.[/quote]

Security Image:

Enter The Letters From The Security Image:

Preview Post Cancel

Last 10 Posts (In reverse order)
denman	Posted: Thursday, October 18, 2012 4:23:52 AM(UTC)
	If it is wired up 3-wire then any bare metal on the frame is Neutral (ground). Also the center terminal (white) on the terminal strip is Neutral.
	THIS FORUM IS DEAD!!!!!!!
lasportsman	Posted: Thursday, October 18, 2012 3:00:12 AM(UTC)
	Thank's. I understad the procedure, except how(where) do you connect the meter to neutral ? Larry
lasportsman	Posted: Wednesday, October 17, 2012 4:35:28 AM(UTC)
	both the surface & oven lights work. Larry
denman	Posted: Wednesday, October 17, 2012 3:59:26 AM(UTC)
	Here are your parts Parts for Frigidaire FEF366CCE Range - AppliancePartsPros.com Here is a better copy of your wiring diagram. http://manuals.frigidaire.com/p...pringfield/316255311.pdf Do the oven light and the surface indicator lights work. If not then you may have a power problem (no neutral). Try flipping the breaker off/on slowly a couple times. Sometimes you can loose half the line without actually tripping the breaker. Check the voltage at the plug L1 to L2 should be 240 volts L1 to Neutral and L2 to Neutral, both should be 120 volts. If OK Unplug the unit and check the wires at the terminal strip in the machine to make sure none are loose or burned out If OK Check the power at the terminal strip. Do this with the heater off and on. Be careful as 240 volts is lethal !!! If the lights work then probably the control board (Item 20 in Backguard Parts) is shot. You will also probably need a new overlay (Item 20A), the old one may get messed up trying to remove it. I would check all the wires going to the control board especially L1 and Neutral. You cold also check that the board is getting power but this can be a pain to do due to the limited space.
	THIS FORUM IS DEAD!!!!!!!
lasportsman	Posted: Wednesday, October 17, 2012 3:43:15 AM(UTC)
	the control panel for the oven & clock doesn't work, no display at all. the oven doesn't work. all surface element's do work. Larry

Important Information: The AppliancePartsPros.com uses cookies. By continuing to browse this site, you are agreeing to our use of cookies. More Details Close