Customer Support 7 days a week

Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

2 Pages12>
New Topic Post Reply
Options
Go to last post Go to first unread
arkie102  
#1 Posted : Thursday, August 13, 2009 5:35:27 PM(UTC)
Quote
arkie102

Rank: Member

Groups: Registered
Joined: 7/31/2009(UTC)
Posts: 17

Spin cycle to slow in all wash/spin speed selections. Tub empties ok but at end of cycle cloths are still wet enough to ring a bit of water. At the end of the cycle I can not here the normal brake action. I have changed the belt. Turning the pully clockwise oscilates the agitator and turning the pully counter clockwise the pully turns. I have also changed the Wash/spin speed switch. If the problem may be the Brake can it be adjusted, If so how.

I have checke all the possible things ,kinked hose ,tub seal, etc:confused:

Wes
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com
 
boshman  
#2 Posted : Thursday, August 13, 2009 9:12:23 PM(UTC)
Quote
boshman

Rank: Member

Groups: Registered
Joined: 5/11/2009(UTC)
Posts: 9

the clothes is still wet because the basket is not spinning fast enough. do this put it in spin mode for say 4 minutes. stop the washer if the brake stator is hot u got a bad pulley. replace the pulley since it is not pushing the spring brake rotor far enough to allow free basket drive rotation.
richappy  
#3 Posted : Friday, August 14, 2009 1:39:40 AM(UTC)
Quote
richappy

Rank: Advanced Member

Groups: Senior Expert
Joined: 9/10/2007(UTC)
Posts: 9,586

Was thanked: 2 time(s) in 2 post(s)
I would shine a light in the spin basket to look for something stuck in the tub.
If ok, you might have bad spin bearings, pull front cover and check.
arkie102  
#4 Posted : Friday, August 14, 2009 12:58:05 PM(UTC)
Quote
arkie102

Rank: Member

Groups: Registered
Joined: 7/31/2009(UTC)
Posts: 17

Originally Posted by: richappy Go to Quoted Post
I would shine a light in the spin basket to look for something stuck in the tub.
If ok, you might have bad spin bearings, pull front cover and check.



nothing stuck in tub. I pulled front panel all I see is the motor, pump and Agitator shaft which is a sealed unit which must be connected to the main pully. Nothing smoking or hot on unit.:confused:

wes
richappy  
#5 Posted : Friday, August 14, 2009 2:16:11 PM(UTC)
Quote
richappy

Rank: Advanced Member

Groups: Senior Expert
Joined: 9/10/2007(UTC)
Posts: 9,586

Was thanked: 2 time(s) in 2 post(s)
Any dirty water coming out of the bottom of the tub.
arkie102  
#6 Posted : Friday, August 14, 2009 3:20:57 PM(UTC)
Quote
arkie102

Rank: Member

Groups: Registered
Joined: 7/31/2009(UTC)
Posts: 17

Originally Posted by: richappy Go to Quoted Post
Any dirty water coming out of the bottom of the tub.
No.

If the transmission is bad , would the washer still agitate but cause the washer to spin solw.:confused:
wes
arkie102  
#7 Posted : Tuesday, August 18, 2009 4:05:31 PM(UTC)
Quote
arkie102

Rank: Member

Groups: Registered
Joined: 7/31/2009(UTC)
Posts: 17

Originally Posted by: arkie102 Go to Quoted Post
No.

If the transmission is bad , would the washer still agitate but cause the washer to spin solw.:confused:
wes


Would appreciate a reply before I replace transsmission.:confused:Wes
richappy  
#8 Posted : Wednesday, August 19, 2009 12:28:29 AM(UTC)
Quote
richappy

Rank: Advanced Member

Groups: Senior Expert
Joined: 9/10/2007(UTC)
Posts: 9,586

Was thanked: 2 time(s) in 2 post(s)
Turn the tranny pulley in the spin direction. If the tranny will not spin, you need a new pulley with thrust washers.
richappy  
#9 Posted : Wednesday, August 19, 2009 4:16:16 PM(UTC)
Quote
richappy

Rank: Advanced Member

Groups: Senior Expert
Joined: 9/10/2007(UTC)
Posts: 9,586

Was thanked: 2 time(s) in 2 post(s)
If you see white shavings under the washer, you have a bad snubber. Post results.
arkie102  
#10 Posted : Tuesday, August 25, 2009 10:49:59 AM(UTC)
Quote
arkie102

Rank: Member

Groups: Registered
Joined: 7/31/2009(UTC)
Posts: 17

Originally Posted by: arkie102 Go to Quoted Post
Spin cycle to slow in all wash/spin speed selections. Tub empties ok but at end of cycle cloths are still wet enough to ring a bit of water. At the end of the cycle I can not here the normal brake action. I have changed the belt. Turning the pully clockwise oscilates the agitator and turning the pully counter clockwise the pully turns. I have also changed the Wash/spin speed switch. If the problem may be the Brake can it be adjusted, If so how.

I have checke all the possible things ,kinked hose ,tub seal, etc:confused:

Wes


UPDATE: Problem solved. Transmission replaced now works fine.Washer less than three years old and only had 1yr warranty. I was lucky Maytag sold me the transmission for 50% off. Thanks for you help. I will add that it is a costly repair parts and labor. A new transmission $144.00 shipping and handling/labor $150/service charge$65.00:mad: :)

Wes
Quick Reply Show Quick Reply
Users browsing this topic
2 Pages12>
New Topic Post Reply
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.