Washer Repair

Richduet · #1 (**permalink**) 12-09-2007, 05:54 PM

Help!! My Duet has died! Worked fine until about an hour ago. Lights were on and seem to respond to control panel. It just would not start a cycle. Unplugged it for few minutes and plugged it back in. Now it's completely dead! No lights....nothing. I know that there are 2 computers. Which should I replace first or should I just do both? Or could there be another issue?? Any help is appreciated!! Rich
MCB (Motor Control Board) part number - 8182706

OR

CCB (Computer Control Board) part number -
8181924

jdappl07 · #2 (**permalink**) 12-09-2007, 06:07 PM

check your owners manual i think it has a 5 year warranty on both control boards but i would follow the wires from the power supply and make sure i had 120 going to the CCB which is useally at the top

Richduet · #3 (**permalink**) 12-09-2007, 06:40 PM

2 years on electronic components.... I will check voltage and get back with you. Thanks! Rich

Richduet · #4 (**permalink**) 12-11-2007, 10:46 AM

Yes it has 120 volts going to the CCB. I think I should order that first???

jdappl07 · #5 (**permalink**) 12-11-2007, 07:35 PM

yeah i woul go for that first

jdappl07 · #6 (**permalink**) 12-11-2007, 07:37 PM

th MCB pretty much controls the motor and the pump

Richduet · #7 (**permalink**) 01-17-2008, 05:47 AM

Thanks for your help. I replaced the CCB and it worked!

I have ordered parts from you site as well. Best prices on the net!

Davetheman7 · #8 (**permalink**) 09-26-2009, 05:28 PM

Quote:

Originally Posted by Richduet

Thanks for your help. I replaced the CCB and it worked!

I have ordered parts from you site as well. Best prices on the net!

My washer seems to be doing the same thing. Started a load, a few minutes into the cycle it stopped and started beeping and displayed a F09 code I believe it was, then the door would not open, and now it wont even power up at all. The buttons wont respond or light up even. How difficult is it to swap out the CCU? I'm not even sure how to take the thing apart to get at it. Any advise is GREATLY appreciated! Thanks

Davetheman7 · #9 (**permalink**) 09-27-2009, 04:34 PM

Anybody? I would like to know if there is anything I should know before replacing the ccu. Thanks

denman · #10 (**permalink**) 09-28-2009, 05:47 AM

Here are your parts
Replacement parts for WHIRLPOOL GHW9200LW0 | AppliancePartsPros.com

Here is the tech sheet
http://www.servicematters.com/docs/w...%208181790.pdf

And a manual
https://secured.whirlpool.com/Servic...0Job%20Aid.pdf

Try to run the diagnostics and other tests to confirm that the board is shot before replacing.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Dead Whirlpool Duet Fault Code F11	Jmbo60	Washer Repair	2	11-07-2009 08:26 AM
Whirlpool duet is dead	woodyl73	Washer Repair	7	05-15-2009 04:55 PM
Whirlpool Duet	DN1234	Washer Repair	0	05-03-2009 06:11 AM
Whirlpool Duet Washer Dead	birddog72	Washer Repair	4	02-19-2009 09:27 AM
GHW9200LW Control Trouble	Frustrated Carl	Washer Repair	0	01-12-2008 05:00 PM

Help! Dead Whirlpool Duet GHW9200LW

Washer Repair

Help!! My Duet has died! Worked fine until about an hour ago. Lights were on and seem to respond to