Register | FAQ's | New Posts | Today's Posts | Extras
Appliance Repair Forum > Search Forums » Search Results

Showing results 1 to 25 of 500
Search took 0.09 seconds.
Search: Posts Made By: fairbank56
Forum: Dryer Repair 11-23-2014, 02:06 PM
Replies: 1
Views: 115
Posted By fairbank56
Remove the toe panel and check the thermal fuse...

Remove the toe panel and check the thermal fuse on the blower housing (two blue wires). Motor will not run if it is blown.

Eric
Forum: Washer Repair 11-21-2014, 03:18 PM
Replies: 1
Views: 143
Posted By fairbank56
Check the pressure hose that runs from the right...

Check the pressure hose that runs from the right rear part of the tub to the water level pressure switch inside the control panel. You may have pinched it or pulled it loose.

Eric
Forum: Dryer Repair 11-20-2014, 08:30 PM
Replies: 14
Views: 654
Posted By fairbank56
The motor winding resistances read low because...

The motor winding resistances read low because you are measuring them in parallel. You must activate the centrifugal switch and then check each winding. 4 to 5 for the run winding and 4 to 3 for the...
Forum: Washer Repair 11-20-2014, 08:10 PM
Replies: 1
Views: 133
Posted By fairbank56
You need to replace the agitator dogs. These...

You need to replace the agitator dogs. These drive the auger in the clockwise direction when the lower agitator goes in the clockwise direction. The auger is only driven in the clockwise direction so...
Forum: Washer Repair 11-20-2014, 07:57 PM
Replies: 1
Views: 122
Posted By fairbank56
Take the lid switch out and have a good look at...

Take the lid switch out and have a good look at it. This type is very prone to coming apart. It can be glued back together or cinched with a small tie wrap. If it does not appear to be coming apart,...
Forum: Dryer Repair 11-19-2014, 12:52 PM
Replies: 2
Views: 185
Posted By fairbank56
This would be a faulty control board. The motor...

This would be a faulty control board. The motor is turned on/off by a relay on the control board.

GE WE04M10004 Board Asm. Mounted - AppliancePartsPros.com...
Forum: Washer Repair 11-18-2014, 02:09 PM
Replies: 3
Views: 145
Posted By fairbank56
The bottom part of the agitator should go back...

The bottom part of the agitator should go back and forth while the top part is only driven in the clockwise direction. If the bottom part is only going in one direction, which sounds like your...
Forum: Washer Repair 11-17-2014, 01:46 PM
Replies: 2
Views: 174
Posted By fairbank56
Transmission is not serviceable so go ahead and...

Transmission is not serviceable so go ahead and replace it. The tub nut can be difficult to remove. It is reverse threaded and we generally use a special spanner wrench and small sledge hammer to get...
Forum: Dryer Repair 11-16-2014, 07:57 AM
Replies: 14
Views: 654
Posted By fairbank56
The guy in the video doesn't know what he is...

The guy in the video doesn't know what he is talking about. He has it hooked up wrong and his explanation as to how it works is wrong. Yes, it will work the way he is connecting things but it is...
Forum: Washer Repair 11-15-2014, 07:36 AM
Replies: 1
Views: 114
Posted By fairbank56
Here is your tech sheet. Eric

Here is your tech sheet.

Eric
Forum: Dryer Repair 11-15-2014, 06:48 AM
Replies: 14
Views: 654
Posted By fairbank56
Well, as usual, trying to do electrical...

Well, as usual, trying to do electrical troubleshooting over a forum with a rookie is an exercise in frustration. Sorry, not your fault. I would suggest making a cheater cord out of an old extension...
Forum: Washer Repair 11-14-2014, 07:16 PM
Replies: 2
Views: 158
Posted By fairbank56
Reset what? Check for loose lid hinge screws on...

Reset what? Check for loose lid hinge screws on left side hinge. That hinge operates the hidden lid switch.

Eric
Forum: Dryer Repair 11-14-2014, 02:44 PM
Replies: 2
Views: 150
Posted By fairbank56
Does it do the same when set to air fluff? Eric

Does it do the same when set to air fluff?

Eric
Forum: Washer Repair 11-14-2014, 06:03 AM
Replies: 1
Views: 143
Posted By fairbank56
Most likely it's a faulty lid switch. Whirlpool...

Most likely it's a faulty lid switch.

Whirlpool 3949247 Lid Switch Assembly - AppliancePartsPros.com (http://www.appliancepartspros.com/whirlpool-lid-switch-assembly-3949247-ap3100003.html)

Eric
Forum: Washer Repair 11-14-2014, 06:00 AM
Replies: 1
Views: 93
Posted By fairbank56
It is normal to have no spin cycle after wash and...

It is normal to have no spin cycle after wash and to get a low fill level in rinse cycle unless you have the fabric softener switch turned on if that is what you are talking about.

Eric
Forum: Washer Repair 11-13-2014, 03:39 PM
Replies: 6
Views: 205
Posted By fairbank56
Take the front panel off and try rotating the...

Take the front panel off and try rotating the motor pulley by hand. One direction is for agitation, the opposite for spin. If it's locked up, take the belt off and try again. Try running motor...
Forum: Washer Repair 11-13-2014, 03:33 PM
Replies: 2
Views: 183
Posted By fairbank56
Are you sure your not getting 9 flashes, then...

Are you sure your not getting 9 flashes, then pause and repeat? That would be a faulty brake resistor which would cause the motor to spin the basket slowly.

Eric
Forum: Washer Repair 11-13-2014, 03:27 PM
Replies: 2
Views: 136
Posted By fairbank56
What's the model number? Washer should drain for...

What's the model number? Washer should drain for 2 minutes without spinning, then motor should pause for a few seconds and start again at which point it should start spinning while continuing to...
Forum: Washer Repair 11-13-2014, 07:36 AM
Replies: 6
Views: 205
Posted By fairbank56
What model year is it and is it a top...

What model year is it and is it a top loader?

Eric
Forum: Washer Repair 11-13-2014, 07:34 AM
Replies: 2
Views: 201
Posted By fairbank56
Does it stop filling when you turn the washer off...

Does it stop filling when you turn the washer off or do you have to shut off the valve at the wall? If you have to turn the wall valve off, then looks like a faulty water inlet assembly. Otherwise,...
Forum: Washer Repair 11-13-2014, 07:21 AM
Replies: 6
Views: 205
Posted By fairbank56
Model number???

Model number???
Forum: Dryer Repair 11-12-2014, 05:40 PM
Replies: 14
Views: 654
Posted By fairbank56
You are bypassing the relay when you operate the...

You are bypassing the relay when you operate the start switch. The start switch and relay are in parallel. You activate the start switch which should start the motor and signal the control board to...
Forum: Washer Repair 11-12-2014, 05:56 AM
Replies: 3
Views: 167
Posted By fairbank56
Disconnect the pressure hose from the pressure...

Disconnect the pressure hose from the pressure switch. If it now starts filling every time when you pull the timer knob then you need to check for clogging in the hose and air chamber on the side of...
Forum: Dryer Repair 11-11-2014, 08:21 PM
Replies: 9
Views: 284
Posted By fairbank56
Should be 4 knobs including timer but you only...

Should be 4 knobs including timer but you only have to take the temp switch knob off. You are not removing the front panel, just opening it to gain access to the inside of it. You must remove the...
Forum: Dryer Repair 11-11-2014, 06:58 PM
Replies: 9
Views: 284
Posted By fairbank56
Unplug dryer, pull the temp switch knob off....

Unplug dryer, pull the temp switch knob off. Remove two screws on back of each end cap on the control panel. Pull control panel forward and lift to access inside of control panel. Lift the tab on one...
Showing results 1 to 25 of 500

 
Forum Jump


All times are GMT -7. The time now is 08:42 AM.

The content on this web site is for informational purposes only and is not intended to replace an on-site diagnosis from a qualified appliance service technician. By reading any content on this site you agree to AppliancePartsPros.com , Inc. disclaimer and Terms of Use.
Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17