Register | FAQ's | New Posts | Today's Posts | Extras
Appliance Repair Forum > Search Forums » Search Results

Showing results 1 to 25 of 500
Search took 0.20 seconds.
Search: Posts Made By: sidfink43
Forum: Washer Repair 11-23-2014, 07:20 PM
Replies: 1
Views: 132
Posted By sidfink43
No guarantees of course but I think you will be...

No guarantees of course but I think you will be find just replacing the tub seal. After you do so operate it with the front panel off to make sure you have fixed the leak.
Forum: Washer Repair 11-22-2014, 07:56 PM
Replies: 1
Views: 138
Posted By sidfink43
I would first check out the thrust bearing and...

I would first check out the thrust bearing and make sure it is installed correctly and that it is allowing the brakes to release.

If the thrust bearing is okay, then you can go into the brake...
Forum: Washer Repair 11-22-2014, 07:52 PM
Replies: 1
Views: 104
Posted By sidfink43
Take off the hot water hose and stick it in the...

Take off the hot water hose and stick it in the laundry sink and see if the flow is steady, which it probably will be. If it is not the problem is with your hot water heater.

If the flow is steady...
Forum: Washer Repair 11-22-2014, 07:45 PM
Replies: 1
Views: 134
Posted By sidfink43
It is very unusual for this to happen. Check the...

It is very unusual for this to happen. Check the straps at the top but I would say it is likely you have just one bad rod and you can just replace it and life should be fine. If you want to be safe...
Forum: Washer Repair 11-20-2014, 05:31 PM
Replies: 3
Views: 163
Posted By sidfink43
No, replacing the rear bearing would not be that...

No, replacing the rear bearing would not be that much, but it could be in the $400 to $500 range and then you would have a lot of money in an older washer.

If you do not need a front loader my...
Forum: Washer Repair 11-19-2014, 06:06 PM
Replies: 3
Views: 163
Posted By sidfink43
Take off the back and check the support structure...

Take off the back and check the support structure for a crack or a break. If that is okay then it may be the rear bearing is failing in which case the cost of the repair means a new machine is in...
Forum: Washer Repair 11-17-2014, 02:06 PM
Replies: 6
Views: 198
Posted By sidfink43
correction, L-78. Check to make sure that is for...

correction, L-78. Check to make sure that is for the Duet Sport which is what I think you have.
Forum: Washer Repair 11-17-2014, 02:04 PM
Replies: 6
Views: 198
Posted By sidfink43
Do a search for Whirlpool manual L-68 which is...

Do a search for Whirlpool manual L-68 which is for an earlier version of your machine. You should be able to download it for free or for a nominal cost. I don't know if there is a service manual...
Forum: Washer Repair 11-17-2014, 12:23 PM
Replies: 6
Views: 198
Posted By sidfink43
Right, use the meter to make certain current is...

Right, use the meter to make certain current is getting to the washer and then you will use it to check the MCU.
Forum: Washer Repair 11-17-2014, 11:04 AM
Replies: 3
Views: 144
Posted By sidfink43
This machine has a brake which engages during...

This machine has a brake which engages during agitation to stop the tub from spinning while in agitation mode. It sounds like the brakes are hung up and not working.
Forum: Washer Repair 11-17-2014, 11:01 AM
Replies: 1
Views: 140
Posted By sidfink43
My prejudice is strongly against the models. ...

My prejudice is strongly against the models. Electronic controls like the one on your machine hate vibration, moisture and heat. Electronic controls on washers have . . .

I suggest you treat...
Forum: Washer Repair 11-17-2014, 10:58 AM
Replies: 1
Views: 141
Posted By sidfink43
I don't know that you can. Here is the diagram...

I don't know that you can. Here is the diagram of your model.

Parts for Whirlpool WFW8300SW05: Control Panel Parts - AppliancePartsPros.com...
Forum: Washer Repair 11-17-2014, 10:55 AM
Replies: 6
Views: 198
Posted By sidfink43
Sounds like the main control unit is blown, which...

Sounds like the main control unit is blown, which shouldn't happen but . . .

Use a meter to check that you have current. Then try changing it out. If you buy from this site and that is not the...
Forum: Washer Repair 11-17-2014, 10:53 AM
Replies: 1
Views: 127
Posted By sidfink43
The PA means that the control unit went through a...

The PA means that the control unit went through a diagnostic process and did not find or generate any error codes.

Your problem is symptomatic of problems with the models with electronic controls,...
Forum: Washer Repair 11-14-2014, 09:55 AM
Replies: 2
Views: 179
Posted By sidfink43
Take off the cabinet and see if there isn't a...

Take off the cabinet and see if there isn't a break in the support structure. If you cannot see anything operate it with the cabinet off and the problem should be apparent.

If it is a structural...
Forum: Washer Repair 11-13-2014, 06:53 AM
Replies: 1
Views: 169
Posted By sidfink43
The first thing you want to check is the pump, it...

The first thing you want to check is the pump, it might be jammed in a way that allows it to turn only in one direction. Then check the coupling.

If these are not the problem the transmission may...
Forum: Washer Repair 11-13-2014, 06:48 AM
Replies: 1
Views: 135
Posted By sidfink43
Operate it with the front panel off. You can...

Operate it with the front panel off. You can take the front panel off by inserting a flat blade screw driver or stiff putty knife in the gap between the top and front near the edges to release clips...
Forum: Washer Repair 11-13-2014, 06:46 AM
Replies: 1
Views: 121
Posted By sidfink43
See if you can find the tech notes which are...

See if you can find the tech notes which are under the top cover or inside the lower service panel. They will show you how to do some testing and diagnostic work.

This is probably not the main...
Forum: Washer Repair 11-10-2014, 06:47 PM
Replies: 1
Views: 178
Posted By sidfink43
This model is showing that it uses agitator dogs....

This model is showing that it uses agitator dogs. Here is the kit

AP3138838

See if that doesn't fix things. And note the nice video APP has prepared.
Forum: Washer Repair 11-09-2014, 05:18 AM
Replies: 3
Views: 245
Posted By sidfink43
Not sure if there is a definitive test but if the...

Not sure if there is a definitive test but if the motor is turning and the transmission pulley is free then it would seem the clutch is the likely suspect.
Forum: Washer Repair 11-08-2014, 07:42 PM
Replies: 3
Views: 245
Posted By sidfink43
I think the clutch assembly is the problem, but...

I think the clutch assembly is the problem, but it is an expensive part. If you buy it from this site and it does not fix the problem you can return it.
Forum: Washer Repair 11-08-2014, 07:39 PM
Replies: 3
Views: 262
Posted By sidfink43
The bearing is a problem that usually impacts the...

The bearing is a problem that usually impacts the spin cycle. If there is an intermittent noise it could be something in the drive shaft, but I expect that you will hear the noise coming from the...
Forum: Washer Repair 11-07-2014, 06:47 PM
Replies: 3
Views: 262
Posted By sidfink43
Operate it with the cabinet off and listen for...

Operate it with the cabinet off and listen for the noise in the transmission.
Forum: Washer Repair 11-07-2014, 06:46 PM
Replies: 1
Views: 181
Posted By sidfink43
There could be a problem with the motor/inverter...

There could be a problem with the motor/inverter assembly but change out the fuse again. If it still blows you may have to change out the motor/inverter just to see if that fixes things. If you buy...
Forum: Washer Repair 11-07-2014, 06:40 PM
Replies: 1
Views: 156
Posted By sidfink43
See if this link to a service manual is the one...

See if this link to a service manual is the one for your model.

http://www.emaservicetips.com/pdfs/490_3cuftHorizontalAxisWasherSM.pdf
Showing results 1 to 25 of 500

 
Forum Jump


All times are GMT -7. The time now is 05:17 PM.

The content on this web site is for informational purposes only and is not intended to replace an on-site diagnosis from a qualified appliance service technician. By reading any content on this site you agree to AppliancePartsPros.com , Inc. disclaimer and Terms of Use.
Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17