Register | FAQ's | New Posts | Today's Posts | Extras
Appliance Repair Forum > Search Forums » Search Results

Showing results 1 to 25 of 500
Search took 0.18 seconds.
Search: Posts Made By: Joe / APP Team
Forum: Oven Repair (including Ranges and Cooktops) 05-31-2018, 12:34 PM
Replies: 22
Views: 20,771
Posted By Joe / APP Team
Regier, You're Very Welcome !!! Yes you will...

Regier, You're Very Welcome !!! Yes you will need the door S/C latch assembly. The control board/panel is designed to constantly check the door switch circuits, even in the TOD (time of day)mode. If...
Forum: Oven Repair (including Ranges and Cooktops) 05-21-2018, 09:49 AM
Replies: 22
Views: 20,771
Posted By Joe / APP Team
Regier, Correct, the two blue wires (18-20 VAC)...

Regier, Correct, the two blue wires (18-20 VAC) from the control transformer is the power supply for the display, signal and the communication to the relays. If you have the voltage across the two...
Forum: Oven Repair (including Ranges and Cooktops) 05-21-2018, 08:02 AM
Replies: 22
Views: 20,771
Posted By Joe / APP Team
Regier, If you have 120 VAC into the control...

Regier, If you have 120 VAC into the control transformer, and 18-20 VAC across the blue wires (JP03/3 & JP03/2) then you have power into the control
board. You can check for line voltage into the...
Forum: Oven Repair (including Ranges and Cooktops) 05-03-2018, 07:48 AM
Replies: 22
Views: 20,771
Posted By Joe / APP Team
Regier, There are several things to check, start...

Regier, There are several things to check, start at the control transformer. Make sure you have 120 VAC across the black and white wires and 18 to 24 VAC across the two blue wires at the control...
Forum: Dryer Repair 04-06-2018, 12:21 PM
Replies: 7
Views: 603
Posted By Joe / APP Team
John, Depending on the meter, if you have a 10k...

John, Depending on the meter, if you have a 10k setting(or in your case a 20k setting) the 1k or rx1 setting is too low to read the proper resistance and you won't register a reading. On the higher...
Forum: Dryer Repair 04-06-2018, 11:01 AM
Replies: 7
Views: 603
Posted By Joe / APP Team
John, That's a tad bit high, should be 10K ohms...

John, That's a tad bit high, should be 10K ohms at room temperature(77 dgrs.F.)see the attached tech sheet for testing and accessing the components needing to be checked.
Forum: Dryer Repair 04-06-2018, 09:49 AM
Replies: 7
Views: 603
Posted By Joe / APP Team
John, check and make sure the heater element and...

John, check and make sure the heater element and wiring aren't shorted to ground, and/or the gas valve isn't "sticking" open. Then replace the thermistor, as a possible issue. A proper model number...
Forum: Dryer Repair 04-06-2018, 09:30 AM
Replies: 7
Views: 603
Posted By Joe / APP Team
John, Check and make sure the duct under the lint...

John, Check and make sure the duct under the lint filter and the blower housing and wheel are not blocked with lint or obstructions. Check the vent hood to make sure it's not blocked or damaged, etc....
Forum: Washer Repair 04-06-2018, 07:46 AM
Replies: 4
Views: 503
Posted By Joe / APP Team
Jogrodz, The noise and no spin situation is most...

Jogrodz, The noise and no spin situation is most likely due to a problem in the mode shifter/clutch assembly, as long as the belt and pulley are OK. Use the tech data sheet to review the error codes,...
Forum: Washer Repair 04-06-2018, 07:10 AM
Replies: 6
Views: 554
Posted By Joe / APP Team
Pkeresz, You're very welcome !! Let us know what...

Pkeresz, You're very welcome !! Let us know what you find. Thanks,
Forum: Washer Repair 04-05-2018, 07:39 AM
Replies: 6
Views: 554
Posted By Joe / APP Team
Ohm, Thanks for attaching the wiring diagram. It...

Ohm, Thanks for attaching the wiring diagram. It may make it easier for pkeresz to repair his dryer. Thanks Again,
Forum: Washer Repair 04-03-2018, 08:08 AM
Replies: 4
Views: 503
Posted By Joe / APP Team
jogrodz, Is the lid latching ? and the tub moves...

jogrodz, Is the lid latching ? and the tub moves freely if you turn it by hand ? You may want to access the control console and retrieve the Tech Data Sheet and review the error codes logged by the...
Forum: Washer Repair 04-03-2018, 07:44 AM
Replies: 6
Views: 554
Posted By Joe / APP Team
Pkeresz, Make sure the belt and belt switch and...

Pkeresz, Make sure the belt and belt switch and wires are OK. Since you've bypassed most of the safety devices with no improvement, you'll need to check the machine control board for 120 VAC out to...
Forum: Dishwasher Repair 03-26-2018, 12:59 PM
Replies: 19
Views: 29,198
Posted By Joe / APP Team
Clothierti, The codes you supplied indicate an...

Clothierti, The codes you supplied indicate an issue in the drive system. There are several things to check, before you dismantle the stator , rotor and RPS sensor. A stuck article between the tubs,...
Forum: Refrigerator & Freezer Repair 02-19-2018, 03:54 PM
Replies: 10
Views: 12,709
Posted By Joe / APP Team
Our12, We rechecked and verified the procedure....

Our12, We rechecked and verified the procedure. Once you remove the outer decorator panels, Look at the bottom edge of the facade/panel there should be two(2) slots molded into the facade, place a...
Forum: Refrigerator & Freezer Repair 02-19-2018, 03:54 PM
Replies: 10
Views: 12,709
Posted By Joe / APP Team
Our12, We rechecked and verified the procedure....

Our12, We rechecked and verified the procedure. Once you remove the outer decorator panels, Look at the bottom edge of the facade/panel there should be two(2) slots molded into the facade, place a...
Forum: Refrigerator & Freezer Repair 02-19-2018, 03:54 PM
Replies: 10
Views: 12,709
Posted By Joe / APP Team
Our12, We rechecked and verified the procedure....

Our12, We rechecked and verified the procedure. Once you remove the outer decorator panels, Look at the bottom edge of the facade/panel there should be two(2) slots molded into the facade, place a...
Forum: Refrigerator & Freezer Repair 02-19-2018, 03:53 PM
Replies: 10
Views: 12,709
Posted By Joe / APP Team
Our12, We rechecked and verified the procedure....

Our12, We rechecked and verified the procedure. Once you remove the outer decorator panels, Look at the bottom edge of the facade/panel there should be two(2) slots molded into the facade, place a...
Forum: Refrigerator & Freezer Repair 01-23-2018, 08:17 AM
Replies: 22
Views: 5,710
Posted By Joe / APP Team
Ptim2002, The hinge has two "fingers"...

Ptim2002, The hinge has two "fingers" that once installed and released, hold the drawer rail system to the drawer panel. The lower finger has a swivel lock on it, you need to bring the two fingers...
Forum: Washer Repair 12-07-2017, 06:23 AM
Replies: 18
Views: 51,633
Posted By Joe / APP Team
BRT123, Happy Mom didn't post a response or an...

BRT123, Happy Mom didn't post a response or an update. But , Like her and most of the people on this thread, you most likely have a problem with the user interface tabs, so you'll need to remove...
Forum: Dishwasher Repair 12-04-2017, 08:53 AM
Replies: 5
Views: 2,504
Posted By Joe / APP Team
Beowing, Thanks for posting your experience with...

Beowing, Thanks for posting your experience with your Bosch dishwasher repair. We're glad to hear your machine is up and running properly and cleaning the dishes. Great Job !!! Thanks Again,
Forum: Oven Repair (including Ranges and Cooktops) 10-30-2017, 11:51 AM
Replies: 27
Views: 41,311
Posted By Joe / APP Team
decorblues, You're almost correct, The...

decorblues, You're almost correct, The ERC/Control monitors certain circuits
constantly, as long as power is supplied, the control monitors the key pad assembly, oven sensor and the door lock switch...
Forum: Dishwasher Repair 10-25-2017, 09:12 AM
Replies: 19
Views: 29,198
Posted By Joe / APP Team
WOW !!! Sounds like the problem was around for a...

WOW !!!
Sounds like the problem was around for a while, before the UL error code was displayed. When it comes to damaged tubs and drive system components, it can get expensive for the parts. With...
Forum: Refrigerator & Freezer Repair 09-22-2017, 07:36 AM
Replies: 18
Views: 4,543
Posted By Joe / APP Team
Mike, OK, make sure you get the splices tight and...

Mike, OK, make sure you get the splices tight and sealed so moisture or condensation can't get in the harness and create problems. Keep in touch.
Forum: Oven Repair (including Ranges and Cooktops) 09-18-2017, 11:12 AM
Replies: 79
Views: 79,509
Posted By Joe / APP Team
GREAT !!! We're glad you worked it out, and...

GREAT !!! We're glad you worked it out, and you're machine is up and running. Great Job. We're here if you need us. Thanks Again,
Showing results 1 to 25 of 500

 
Forum Jump


All times are GMT -7. The time now is 10:17 AM.

The content on this web site is for informational purposes only and is not intended to replace an on-site diagnosis from a qualified appliance service technician. By reading any content on this site you agree to AppliancePartsPros.com , Inc. disclaimer and Terms of Use.
Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17