Register | FAQ's | New Posts | Today's Posts | Extras
Appliance Repair Forum > Search Forums » Search Results

Showing results 1 to 25 of 500
Search took 0.08 seconds.
Search: Posts Made By: fairbank56
Forum: Washer Repair 12-17-2014, 01:59 PM
Replies: 4
Views: 171
Posted By fairbank56
If the transmission is spinning, then the...

If the transmission is spinning, then the transmission is not the problem. Sounds like a problem with the split washer and/or tub nut. Did you use a spanner wrench and hammer to tighten the tub...
Forum: Dryer Repair 12-16-2014, 07:17 AM
Replies: 1
Views: 103
Posted By fairbank56
Could be the timer or the motor switch. Unplug...

Could be the timer or the motor switch. Unplug dryer, disconnect black wire that goes from the timer motor to timer terminal Y. Leave that wire loose but not touching anything. Unplug wire from R...
Forum: Washer Repair 12-16-2014, 06:51 AM
Replies: 6
Views: 205
Posted By fairbank56
Whirlpool 352088 Terminal, Female (disconnect...

Whirlpool 352088 Terminal, Female (disconnect Black) - AppliancePartsPros.com (http://www.appliancepartspros.com/whirlpool-terminal-female-disconnect-352088-ap3073167.html)
Forum: Dryer Repair 12-15-2014, 12:45 PM
Replies: 5
Views: 187
Posted By fairbank56
Then, assuming the door switch and the two...

Then, assuming the door switch and the two thermistors are good, looks like a bad control board. Check the solder connections of the motor relay K1 and the 4 pin wiring receptacle.

GE WE04M10004...
Forum: Washer Repair 12-15-2014, 11:52 AM
Replies: 6
Views: 205
Posted By fairbank56
Standard wiring for the motor is 18awg rated at...

Standard wiring for the motor is 18awg rated at 105C temperature. 12 and 14awg are not necessary and would be too large for the crimp terminal and the insulation would probably not fit into the...
Forum: Washer Repair 12-15-2014, 11:43 AM
Replies: 1
Views: 82
Posted By fairbank56
You must replace the whole lid lock. Whirlpool...

You must replace the whole lid lock.

Whirlpool W10404050 Lid Latch Assembly - AppliancePartsPros.com (http://www.appliancepartspros.com/whirlpool-latch-w10404050-ap5263307.html)

Eric
Forum: Dryer Repair 12-14-2014, 06:06 PM
Replies: 5
Views: 187
Posted By fairbank56
You must test with connector plugged in. We...

You must test with connector plugged in. We sometimes must use needle tip meter probes to get into the back side of the plug or use insulation piercing probes or test clips. Basically, the orange...
Forum: Dryer Repair 12-14-2014, 06:26 AM
Replies: 5
Views: 187
Posted By fairbank56
Belt ok? Check the control outlet thermistor....

Belt ok? Check the control outlet thermistor. Should read between 118-122 kohms at 69 degrees. If good, check voltages at control board 4 pin connector. Should have 120vac between orange and yellow,...
Forum: Dryer Repair 12-12-2014, 03:45 PM
Replies: 3
Views: 119
Posted By fairbank56
Part #803 in this diagram. Switch is activated by...

Part #803 in this diagram. Switch is activated by the idler arm #215.

Eric

Parts for GE DQSR483EE1WW: Backsplash, Blower & Motor Assembly Parts - AppliancePartsPros.com...
Forum: Dryer Repair 12-12-2014, 12:26 PM
Replies: 3
Views: 119
Posted By fairbank56
Something to do with the idler pulley...

Something to do with the idler pulley installation. The arm of the pulley assembly operates the "broken belt" switch. If the switch isn't being activated, you will get the symptoms you are...
Forum: Washer Repair 12-07-2014, 07:46 PM
Replies: 4
Views: 201
Posted By fairbank56
You can bypass the lid switch to operate the...

You can bypass the lid switch to operate the machine with the cabinet off. Then you can observe around the pump and drain hoses looking for the leak while it's running. Drain pump is the white thing...
Forum: Washer Repair 12-07-2014, 06:30 AM
Replies: 4
Views: 201
Posted By fairbank56
That is an 06 model so it's about 8 years old....

That is an 06 model so it's about 8 years old. Probably a leaking drain pump. Remove the cabinet so you can inspect the drain pump and drain hoses.

Cabinet removal:...
Forum: Dryer Repair 12-06-2014, 08:00 AM
Replies: 2
Views: 184
Posted By fairbank56
I think your right. I recently read that it would...

I think your right. I recently read that it would take about 2000 years to view all the video's on youtube!

Eric
Forum: Washer Repair 12-06-2014, 07:43 AM
Replies: 1
Views: 131
Posted By fairbank56
There isn't any mechanical brake on this washer....

There isn't any mechanical brake on this washer. You need to use a spanner wrench and hammer to get this nut off. This is reverse thread so go clockwise to loosen nut. Wack the spanner wrench with...
Forum: Dryer Repair 12-01-2014, 06:46 AM
Replies: 20
Views: 1,038
Posted By fairbank56
As I said before: "Disconnect and jump out...

As I said before: "Disconnect and jump out the two blue wires on the motor relay. If problem still exists, it's not the control board. Try replacing the timer."

You can bypass the timer as well...
Forum: Dryer Repair 11-30-2014, 08:34 PM
Replies: 20
Views: 1,038
Posted By fairbank56
The problem is not the relay. Jumping out the...

The problem is not the relay. Jumping out the relay blue wires means disconnecting the wires and connecting them together which you did. You should absolutely not have connected the two relay pink...
Forum: Dryer Repair 11-30-2014, 05:38 PM
Replies: 1
Views: 144
Posted By fairbank56
The only time that the timer advances in auto dry...

The only time that the timer advances in auto dry is when the cycling thermostat opens or it's at the end of the cycle in cool down (no heat). Monitor the voltage across the cycling thermostat. When...
Forum: Dryer Repair 11-23-2014, 02:06 PM
Replies: 1
Views: 169
Posted By fairbank56
Remove the toe panel and check the thermal fuse...

Remove the toe panel and check the thermal fuse on the blower housing (two blue wires). Motor will not run if it is blown.

Eric
Forum: Washer Repair 11-21-2014, 03:18 PM
Replies: 1
Views: 195
Posted By fairbank56
Check the pressure hose that runs from the right...

Check the pressure hose that runs from the right rear part of the tub to the water level pressure switch inside the control panel. You may have pinched it or pulled it loose.

Eric
Forum: Dryer Repair 11-20-2014, 08:30 PM
Replies: 20
Views: 1,038
Posted By fairbank56
The motor winding resistances read low because...

The motor winding resistances read low because you are measuring them in parallel. You must activate the centrifugal switch and then check each winding. 4 to 5 for the run winding and 4 to 3 for the...
Forum: Washer Repair 11-20-2014, 08:10 PM
Replies: 1
Views: 180
Posted By fairbank56
You need to replace the agitator dogs. These...

You need to replace the agitator dogs. These drive the auger in the clockwise direction when the lower agitator goes in the clockwise direction. The auger is only driven in the clockwise direction so...
Forum: Washer Repair 11-20-2014, 07:57 PM
Replies: 1
Views: 158
Posted By fairbank56
Take the lid switch out and have a good look at...

Take the lid switch out and have a good look at it. This type is very prone to coming apart. It can be glued back together or cinched with a small tie wrap. If it does not appear to be coming apart,...
Forum: Dryer Repair 11-19-2014, 12:52 PM
Replies: 3
Views: 271
Posted By fairbank56
This would be a faulty control board. The motor...

This would be a faulty control board. The motor is turned on/off by a relay on the control board.

GE WE04M10004 Board Asm. Mounted - AppliancePartsPros.com...
Forum: Washer Repair 11-18-2014, 02:09 PM
Replies: 3
Views: 181
Posted By fairbank56
The bottom part of the agitator should go back...

The bottom part of the agitator should go back and forth while the top part is only driven in the clockwise direction. If the bottom part is only going in one direction, which sounds like your...
Forum: Washer Repair 11-17-2014, 01:46 PM
Replies: 2
Views: 222
Posted By fairbank56
Transmission is not serviceable so go ahead and...

Transmission is not serviceable so go ahead and replace it. The tub nut can be difficult to remove. It is reverse threaded and we generally use a special spanner wrench and small sledge hammer to get...
Showing results 1 to 25 of 500

 
Forum Jump


All times are GMT -7. The time now is 07:42 AM.

The content on this web site is for informational purposes only and is not intended to replace an on-site diagnosis from a qualified appliance service technician. By reading any content on this site you agree to AppliancePartsPros.com , Inc. disclaimer and Terms of Use.
Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17