Register | FAQ's | New Posts | Today's Posts | Extras
Appliance Repair Forum > Search Forums » Search Results

Showing results 1 to 20 of 20
Search took 0.07 seconds.
Search: Posts Made By: RandyJ
Forum: Washer Repair 06-06-2014, 09:04 AM
Replies: 0
Views: 243
Posted By RandyJ
Stacked Maytag Washer/Dryer, won't empty water

Dryer appears to be working perfectly. Clothes washer just started having this problem. It was running fine but now it is not pumping the water out. It appears to be running a complete cycle...
Forum: Washer Repair 03-22-2013, 04:44 PM
Replies: 4
Views: 1,005
Posted By RandyJ
Fixed It!

I took another look... could barely see it but a white wire (#9) was loose between the timer and front cover. When I pulled it out the spade terminal had been burned. I removed the timer and found...
Forum: Washer Repair 03-22-2013, 03:58 PM
Replies: 4
Views: 1,005
Posted By RandyJ
Yep... yellow is 22, red is 32. oh yeah... I can...

Yep... yellow is 22, red is 32.
oh yeah... I can hear the timer motor running if that makes any difference. My son also informed me that when he got the front off of the dryer that the breaker in...
Forum: Washer Repair 03-21-2013, 10:11 AM
Replies: 4
Views: 1,005
Posted By RandyJ
Washer (combo) quit working after removing dryer door

My son took the front off of the dryer. A blue wire was hanging loose which he reconnected to the drum (I assume it is a tub sensor wire). There are two wires (red & yellow) in the wiring bundle...
Forum: Washer Repair 12-09-2012, 06:20 PM
Replies: 1
Views: 1,304
Posted By RandyJ
All you appliance repair wizards out there and I...

All you appliance repair wizards out there and I can't get a reply??? Everyone stumped or what?
Forum: Washer Repair 12-09-2012, 06:56 AM
Replies: 7
Views: 2,379
Posted By RandyJ
If you have access to the floor joists it would...

If you have access to the floor joists it would be relatively easy to scab onto the existing floor joists for strength or to add more floor joists. Unless the floor itself is too thin or too weak...
Forum: Washer Repair 12-09-2012, 04:47 AM
Replies: 1
Views: 1,304
Posted By RandyJ
Fills with water, won't run.

I'm working on something that someone else tried to fix... that's the problem! The dryer motor and timer have been replaced and the dryer is working fine. Now, the washer timer runs and it will...
Forum: Dryer Repair 11-16-2012, 10:14 PM
Replies: 10
Views: 2,115
Posted By RandyJ
It is a very good looking unit. I can get a good...

It is a very good looking unit. I can get a good used dryer for @ $150... or get a used motor for about $50. It matches the washer so we'll probably try to fix it. I've already got a re-stringing...
Forum: Dryer Repair 11-16-2012, 05:03 PM
Replies: 10
Views: 2,115
Posted By RandyJ
hmm... so, what I did by connecting L1 (black on...

hmm... so, what I did by connecting L1 (black on timer) to S (purple) should power the motor and make it run? (Just trying to figure out which wires to jump to make motor run for testing puposes).
Forum: Dryer Repair 11-16-2012, 03:52 PM
Replies: 10
Views: 2,115
Posted By RandyJ
black/L1 already checked. That's where I pulled...

black/L1 already checked. That's where I pulled power from to try to jump the timer attempting to get the motor to run by itself.(connected purple to black, L1). It was getting late so we had...
Forum: Dryer Repair 11-16-2012, 01:52 PM
Replies: 10
Views: 2,115
Posted By RandyJ
Thanks denman. I checked as described except...

Thanks denman. I checked as described except that I'm not able to get to the motor to check neutral to "1". The readings I got are
s- 2.0 ohms
m- 2.33 kohms
L-2.55 kohms
L1- 2.33 k ohms
not quite...
Forum: Dryer Repair 11-16-2012, 10:15 AM
Replies: 10
Views: 2,115
Posted By RandyJ
All fuses & thermostats appear to be good...

All fuses & thermostats appear to be good when checked with ohm meter. Looking at the wiring diagram I tried to jump the timer to get the motor to run but nothng happened. I jumped the purple to...
Forum: Dryer Repair 11-15-2012, 06:27 PM
Replies: 10
Views: 2,115
Posted By RandyJ
Dryer quit, won't start again

I've got to go to my mom's tomorrow to check out her dryer. It was running when all of a sudden it quit. At this point all I know is that it still will not start back up and is getting power on...
Forum: Refrigerator & Freezer Repair 11-08-2012, 05:21 AM
Replies: 2
Views: 1,350
Posted By RandyJ
Thanks... Everything appears to work like new...

Thanks... Everything appears to work like new except that it does not cool at all. I took it to a used appliance/service place in my home town. He says probably an evaporator or tube from...
Forum: Refrigerator & Freezer Repair 11-07-2012, 09:09 AM
Replies: 2
Views: 1,350
Posted By RandyJ
Not cooling, compressor runs

Compressor runs, everything appears to work fine. It was cooling good for a couple of years after moving then went down to get a cold beer out of it... oops! Not cold... not even cooling at all...
Forum: Dryer Repair 10-30-2012, 09:10 PM
Replies: 6
Views: 1,476
Posted By RandyJ
Okay. I just looked at that thread and if memory...

Okay. I just looked at that thread and if memory serves me correctly it is the same as the conclusion I came to by using my ohm meter. 1-2 blue, black complete the circuit to the heating elements...
Forum: Dryer Repair 10-30-2012, 09:03 PM
Replies: 6
Views: 1,476
Posted By RandyJ
Thanks. It could be days or even a week or two...

Thanks. It could be days or even a week or two before I go back to where the dryer is... but I will get the model number for sure. All I have available at the moment is the stacked unit at my home...
Forum: Dryer Repair 10-30-2012, 02:42 PM
Replies: 6
Views: 1,476
Posted By RandyJ
I suppose that something is different about those...

I suppose that something is different about those numbers then. It's the number I got off of the motor and it pulls up the same number when I do a search on the internet.... and those two motors...
Forum: Dryer Repair 10-29-2012, 10:51 PM
Replies: 4
Views: 1,744
Posted By RandyJ
I'm a general troubleshooter/handyman, not much...

I'm a general troubleshooter/handyman, not much into appliance repair. With that said... I would use something like a stethoscope to narrow down the source of the noise. Even a stick against...
Forum: Dryer Repair 10-29-2012, 12:01 PM
Replies: 6
Views: 1,476
Posted By RandyJ
Over & Under dry timer crazy after motor replaced

TWO PROBLEMS? (3rd problem is that I'm working on a dryer that someone else has already been working on... I hate that!)

This is not the same unit mentioned in the heading model# but the one I'm...
Showing results 1 to 20 of 20

 
Forum Jump


All times are GMT -7. The time now is 10:58 PM.

The content on this web site is for informational purposes only and is not intended to replace an on-site diagnosis from a qualified appliance service technician. By reading any content on this site you agree to AppliancePartsPros.com , Inc. disclaimer and Terms of Use.
Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17