Refrigerator & Freezer Repair

jermann · #1 (**permalink**) 04-14-2012, 07:15 AM

I was given a GE Profile Arctica. Owner stated ice maker worked, but water dispenser did not. Plugged in and working. Have not hooked up water line yet. Ice maker and ice dispenser power up. Buttons for water, quick ice, lock, alarm, light and filter do nothing. Crushed and cubed buttons beep. No lights on any of them. Ice maker turned off right now. Electronics problem? Does it have to do with the fact the water is not hooked up yet?

jermann · #2 (**permalink**) 04-16-2012, 02:19 PM

Quote:

Originally Posted by jermann

I was given a GE Profile Arctica. Owner stated ice maker worked, but water dispenser did not. Plugged in and working. Have not hooked up water line yet. Ice maker and ice dispenser power up. Buttons for water, quick ice, lock, alarm, light and filter do nothing. Crushed and cubed buttons beep. No lights on any of them. Ice maker turned off right now. Electronics problem? Does it have to do with the fact the water is not hooked up yet?

I saw where Gene suggested the Main Control Board to someone with a seemingly similar problem. Might this be the problem for me? What is the part no. for my model? Also noticed at bottom, below freezer door, an empty female connector at the wire harness, with no male connector. Is this some sort of diagnostic port, or should I look harder for the male end?

Gene · #3 (**permalink**) 04-16-2012, 03:56 PM

Measure the DC voltage between the J4-2 & J4-1 and J4-2 & J4-3 at the main control board (on the back of the fridge) and post the results.

Gene.

jermann · #4 (**permalink**) 04-16-2012, 05:24 PM

Gene, I have 12 volts between J4-2 & J4-1 and 12 volts between J4-2 & J4-3.

Gene · #5 (**permalink**) 04-16-2012, 06:43 PM

Most likely the problem is a bad dispenser control board but there is a small chance for the dispenser interface board to be bad as well.

- The dispenser control board Part number: WR55X10195

- The dispenser interface board Part number: WR55X10298

Gene.

jermann · #6 (**permalink**) 04-17-2012, 04:56 AM

Thanks Gene, Thats what I was thinking. Wires all seem intact and 12 volts makes it to the board. I'll start with the dispenser board. One last question, is there a part no. for an owners manual? Thanks again. I owe you a beer!

Gene · #7 (**permalink**) 04-17-2012, 03:00 PM

You are welcome. I don't think GE sold such manuals.

Keep us posted.

Gene.

jermann · #8 (**permalink**) 04-17-2012, 03:31 PM

Thanks again. Ordered part today. Should have it by Friday. I'll update then. Glad I found this forum. Most useful site on the Web!

Gene · #9 (**permalink**) 04-17-2012, 04:33 PM

BTW, I'm not sure if I got your question right. If you are looking for the Owners Manual then just click on the link. I thought you were looking for the Service manual and this manual is not available.

Gene.

jermann · #10 (**permalink**) 04-17-2012, 07:09 PM

Thanks Gene. That's what I wanted.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
What brands/models have sane power controls?	TyroTechFan	Microwave Repair	0	08-26-2011 03:29 PM
no power to the controls on the door	banjo1234	Dishwasher Repair	3	11-09-2010 06:21 AM
Maytage All power to Controls Is out	676BACK	Washer Repair	1	09-04-2010 06:02 PM
power controls	balls52	Dryer Repair	1	06-03-2009 05:55 PM
oven controls don't work after power outage	nooven	Oven Repair (including Ranges and Cooktops)	1	12-07-2008 02:08 PM

GE Arctica No power to some in door controls

Refrigerator & Freezer Repair

I was given a GE Profile Arctica. Owner stated ice maker worked, but water dispenser did not. Plugged in and