|
|||
 |
|||
| Register | FAQ's | New Posts | Today's Posts | Extras |
| » no water to ice maker but i have water at glass filler in door |
 |
By reading any content on this site you agree to AppliancePartsPros.com, Inc. disclaimer and Terms of Use. |
|
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
07-10-2009, 07:20 PM
|
|||
|
|||
no water to ice maker but i have water at glass filler in door
Model Number: ed27rqxww10 Brand: Whirlpool Age: More than 10 years
I HAVE A WHIRLPOOL SIDE BY SIDE
MODEL #ed27rqxww10, SN#SX1510270, 4-1990 THE ICE MAKER IS NOT GETTING ANY WATER TO MAKE ICE. I CAN GET WATER FROM THE GLASS FILLER IN THE DOOR. THE DOOR DISPENSER WORKS FINE FOR CUBED OR CRUSHED ICE OR WATER I TOOK OFF THE COVER AND FOUND THAT I HAVE A MODULAR ICE MAKER. I HAVE TRIED THE FOLLOWING TROUBLE SHOOTING
I HAVE NOT TRIED TO DO THE T-H TEST AND CHECK THE TO SEE IF I HAVE 120 VOLTS FOR 5-7 SECONDS @ THE END OF THE REVOLUTION IS THERE A WAY I CAN ACTIVATE THE WATER TO THE ICE MACHINE MANUALLY? DO YOU SELL A REPLACEMENT ICE MAKER? PART # ??? WHAT OTHER TEST CAN I TRY THANK YOU JOHN Related Models     
|
|
See inside of your appliance - diagrams and part photos for virtually every model.
powered by AppliancePartsPros.com |
|
07-10-2009, 08:38 PM
|
|||
|
|||
Remove the entire valve and disconnect the discharge lines that feed the refrig/freezer. Get a bucket or large plastic container. Leave the supply line connected to the valve and place it into the container (to catch the water).Locate the solenoid that controls the ice maker fill. Disconnect the wiring connector and hook up a test cord to the terminals. Plug it in and see if you get water. If not, replace it.
__________________
Nemo malus felix
|
|
07-18-2009, 01:16 PM
|
|||
|
|||
|
valve is good
i disconnected solenoid and put power to it.
water comes out of both solenoid when power is applied to each. still no ice?   Last edited by johnelm@tds.net : 07-18-2009 at 01:19 PM.
|
|
07-19-2009, 05:57 PM
|
|||
|
|||
|
With the machine plugged in and the ice maker installed, and the wire bale in the down position, place a jumper wire between T and H. If the motor starts to turn, hold the jumper in place for about half to two thirds of its rotation, then remove it. If it doesn't turn at all, replace the ice maker.
__________________
Nemo malus felix
|
|
07-21-2009, 03:44 PM
|
|||
|
|||
|
test t & h
after testing t h the motor will only turn 1/2 way then stops. is there a replacement ice maker for this unit? part number?? thank you john
|
|
07-22-2009, 09:09 PM
|
|||
|
|||
|
__________________
Nemo malus felix
|
|
07-25-2009, 05:49 PM
|
|||
|
|||
|
i just ordered a new ice maker i hope this works. i will get back to you after i install.
thanks for your help john
|
|
|
See inside of your appliance - diagrams and part photos for virtually every model.
powered by AppliancePartsPros.com |
|
| Thread Tools | Search this Thread |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Kenmore ice maker door water not getting water | fastirwin | Refrigerator & Freezer Repair | 10 | 05-18-2009 04:17 PM |
| Water to door dispnsr-No water to ice maker | ffizzino | Refrigerator & Freezer Repair | 1 | 04-15-2009 04:07 PM |
| Ice Maker Not Working & Water In Door Water | RPETTIGREW | Refrigerator & Freezer Repair | 1 | 04-11-2009 02:26 PM |
| water to door but no water to ice maker | rexbd | Refrigerator & Freezer Repair | 1 | 12-12-2008 04:19 PM |
| Ice maker will not draw water but water in door works normally | kg1okc | Refrigerator & Freezer Repair | 3 | 01-26-2008 03:57 PM |
Linear Mode
