|
|||
 |
|||
| Register | FAQ's | New Posts | Today's Posts | Extras |
| » whirlpool washer problem |
 |
By reading any content on this site you agree to AppliancePartsPros.com, Inc. disclaimer and Terms of Use. |
|
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
|
See inside of your appliance - diagrams and part photos for virtually every model.
powered by AppliancePartsPros.com |
01-08-2009, 10:36 AM
|
|||
|
|||
This is what the tech sheet says on the F1 code
[B][FONT=Swiss721BT-BoldCondensed][SIZE=1][FONT=Swiss721BT-BoldCondensed][SIZE=1][LEFT]Pressure Signal Out-of-Range[/LEFT] [/SIZE][/FONT][/SIZE][/FONT][FONT=Swiss721BT-BoldCondensed][SIZE=1][FONT=Swiss721BT-BoldCondensed][SIZE=1][LEFT]F [/B][/SIZE][/FONT][/SIZE][/FONT][FONT=Swiss721BT-RomanCondensed][SIZE=1][FONT=Swiss721BT-RomanCondensed][SIZE=1]then [/SIZE][/FONT][/SIZE][/FONT][B][FONT=Swiss721BT-BoldCondensed][SIZE=1][FONT=Swiss721BT-BoldCondensed][SIZE=1]1 [/B][/SIZE][/FONT][/SIZE][/FONT][FONT=Swiss721BT-RomanCondensed][SIZE=1][FONT=Swiss721BT-RomanCondensed][SIZE=1]flashes when the control detects an out of range pressure signal.[/LEFT] [/SIZE][/FONT][/SIZE][/FONT][FONT=AdobePiStd][SIZE=1][FONT=AdobePiStd][SIZE=1][LEFT]➔ [/SIZE][/FONT][/SIZE][/FONT][FONT=Swiss721BT-RomanCondensed][SIZE=1][FONT=Swiss721BT-RomanCondensed][SIZE=1]Check pressure hose connection from tub to machine/motor control. Is hose pinched or kinked?[/LEFT] [/SIZE][/FONT][/SIZE][/FONT][FONT=AdobePiStd][SIZE=1][FONT=AdobePiStd][SIZE=1][LEFT]➔ [/SIZE][/FONT][/SIZE][/FONT][FONT=Swiss721BT-RomanCondensed][SIZE=1][FONT=Swiss721BT-RomanCondensed][SIZE=1]If [/SIZE][/FONT][/SIZE][/FONT][B][FONT=Swiss721BT-BoldCondensed][SIZE=1][FONT=Swiss721BT-BoldCondensed][SIZE=1]F [/B][/SIZE][/FONT][/SIZE][/FONT][FONT=Swiss721BT-RomanCondensed][SIZE=1][FONT=Swiss721BT-RomanCondensed][SIZE=1]then [/SIZE][/FONT][/SIZE][/FONT][B][FONT=Swiss721BT-BoldCondensed][SIZE=1][FONT=Swiss721BT-BoldCondensed][SIZE=1]1 [/B][/SIZE][/FONT][/SIZE][/FONT][FONT=Swiss721BT-RomanCondensed][SIZE=1][FONT=Swiss721BT-RomanCondensed][SIZE=1]repeats numerous times after POWER is pressed and the pressure hose connection is not pinched or kinked,[/LEFT] replace the machine/motor control Hope this helps, here's the breakdown [url=http://www.appliancepartspros.com/partsearch/model.aspx?model_id=5134138]Model WTW6600SB2[/url] Nat [/SIZE][/FONT][/SIZE][/FONT]
__________________
-We don't have a fancy website but, we do have fast reliable service in South Central Missouri & do warranty work for Whirlpool, Estate, Maytag, Amana, Frigidaire, Gibson & more. We service most of the South Central Ozarks region. Send us an email at libertyapplservice@yahoo.com We are also Ministers that do a weekly jail house ministry. Rate Liberty Appliance Service on MyPros.com     
|
|
|
See inside of your appliance - diagrams and part photos for virtually every model.
powered by AppliancePartsPros.com |
|
| Thread Tools | Search this Thread |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| whirlpool washer agitator problem | Charles3 | Washer Repair | 3 | 10-30-2009 05:24 PM |
| Whirlpool Thin Twin Washer Problem | mineolabauer | Dryer Repair | 1 | 12-01-2008 09:45 AM |
| Washer problem in LARGE load setting- timer problem? | jagtianis | Washer Repair | 9 | 08-04-2008 03:49 AM |
| Whirlpool washer timer problem | David Smith | Washer Repair | 0 | 06-29-2008 08:07 AM |
| Whirlpool Tub Balance Problem | cmc | Washer Repair | 0 | 06-10-2008 11:44 AM |
Linear Mode
