Customer Support 7 days a week

Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

New Topic Post Reply
Options
Go to last post Go to first unread
vtp1957  
#1 Posted : Tuesday, December 15, 2009 4:17:07 AM(UTC)
Quote
vtp1957

Rank: Member

Groups: Registered
Joined: 12/15/2009(UTC)
Posts: 4

just installed a new 3dryer plug..the dryer was in storage for 5 months dryer starts up but only runs for about 5 sec then shuts off,,,is the dryer bad or was the plug installed wrong
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com
 
denman  
#2 Posted : Tuesday, December 15, 2009 5:06:12 AM(UTC)
Quote
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
A model number may help others help you.

When you say shut off exactly what do you mean re: is it blowing the breaker etc?
Also does the drum manually rotate fairly easily?
Do you have to wait several minutes before you can restart the unit?
If yes it sounds like the motor is overheating and tripping it's internal thermal cut-off.

The more info you can provide about the symptoms the better!!
THIS FORUM IS DEAD!!!!!!!
vtp1957  
#3 Posted : Tuesday, December 15, 2009 6:53:56 AM(UTC)
Quote
vtp1957

Rank: Member

Groups: Registered
Joined: 12/15/2009(UTC)
Posts: 4

no the breaker does not trip..i can move the drum either way easly and yes i do have to wait a couple min. to try it again
denman  
#4 Posted : Tuesday, December 15, 2009 7:33:35 AM(UTC)
Quote
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
Does sound like the motor is overheating.
This can have several causes.

Model Number?
THIS FORUM IS DEAD!!!!!!!
vtp1957  
#5 Posted : Wednesday, December 16, 2009 3:28:34 PM(UTC)
Quote
vtp1957

Rank: Member

Groups: Registered
Joined: 12/15/2009(UTC)
Posts: 4

Originally Posted by: denman Go to Quoted Post
Does sound like the motor is overheating.
This can have several causes.

Model Number?

MODEL # FDE648GFS1

IT WORKED FINE BEFORE I PUT IT IN STORAGE 5 MON. AGO....WHEN I INSTALLEDTHE PLUG I PUT WHITE IN THE CENTER FOR THE L PART OF THE PLUG AND PUT RED AND BLACK ON THE SIDE PART OF THE PLUG...I DONT THINK ITS ANYTHING MAJOR..BUT I AM CONFUSSED
denman  
#6 Posted : Wednesday, December 16, 2009 3:58:44 PM(UTC)
Quote
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
Your wiring hook up seems OK to me.
I am assuming that at your old place it was also a 3 wire hook up.
As there are differences for a 3 or 4 wire hook ups.
Here is a site with info so you can check your wiring
http://www.applianceaid.com/electrical_testing_tips.html

Do you have heat when it runs?
On the motor are 2 centrifugal switches, they are activated once the motor gets close to operating speed.
One switch connects in the heater.
The other switch disconnects the motor's start winding. If it is not disconnected once the motor starts then it will overheat.

So if there is no heat there is a chance that the switch activation mechanism in the motor is not working. Perhaps it has rusted some or it's lubrication has dried up.
THIS FORUM IS DEAD!!!!!!!
vtp1957  
#7 Posted : Wednesday, December 16, 2009 10:04:24 PM(UTC)
Quote
vtp1957

Rank: Member

Groups: Registered
Joined: 12/15/2009(UTC)
Posts: 4

Originally Posted by: denman Go to Quoted Post
Your wiring hook up seems OK to me.
I am assuming that at your old place it was also a 3 wire hook up.
As there are differences for a 3 or 4 wire hook ups.
Here is a site with info so you can check your wiring
http://www.applianceaid.com/electrical_testing_tips.html

Do you have heat when it runs?
On the motor are 2 centrifugal switches, they are activated once the motor gets close to operating speed.
One switch connects in the heater.
The other switch disconnects the motor's start winding. If it is not disconnected once the motor starts then it will overheat.

So if there is no heat there is a chance that the switch activation mechanism in the motor is not working. Perhaps it has rusted some or it's lubrication has dried up.

DRYER ONLY RUNS FOR 4 OR5 SEC SO I DONT KNOW IF THERE IS HEAT CAN THE MOTOR BE FIXED OR DO I REPLACE IT
denman  
#8 Posted : Thursday, December 17, 2009 12:53:45 AM(UTC)
Quote
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
I would open it up and check the motor you may be able to fix it.

Note I am not 100% sure this is your problem as it running only 4 or 5 seconds seems too short of a time for it to build up heat in the motor.

Could be a loose/poor connection that is opening one it heats up a bit so I would check all the wiring going to the motor.
THIS FORUM IS DEAD!!!!!!!
Quick Reply Show Quick Reply
Users browsing this topic
New Topic Post Reply
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.