Customer Support 7 days a week

Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

New Topic Post Reply
Options
Go to last post Go to first unread
greatergraces@yahoo.com  
#1 Posted : Tuesday, November 30, 2010 7:20:08 PM(UTC)
Quote
greatergraces@yahoo.com

Rank: Member

Groups: Registered
Joined: 11/30/2010(UTC)
Posts: 7

the dryer lights up ,does not start.we did turn off power for more than 3min.door is shut.
Sponsor
See inside of your appliance - diagrams and part photos for virtually every model.

powered by AppliancePartsPros.com
 
denman  
#2 Posted : Wednesday, December 1, 2010 12:58:32 AM(UTC)
Quote
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
Here are your parts
Replacement parts for WHIRLPOOL WED6200SW1 29``ELECTRIC DRYER | AppliancePartsPros.com

This should help with the repair
https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/5778291b5b00aa40852571b5005435db/$FILE/8178584.pdf

You will see a thermal fuse (Item 7 in Section 3 of the parts).
This is a likely culprit.

Unplug the unit and check the fuse with a meter should be 0 ohms.

Jiggery Pokery method is.
Unplug the unit.
Remove both wires from the fuse, short them together and tape them up so they will not short to the frame.
Plug the unit in and give it a try.

If blown, replace the fuse ASAP as it is a critical safety device re: prevents lint fires which can turn into house fires.

Also clean/check your vent system and the blower as these are the most common causes of it blowing.
THIS FORUM IS DEAD!!!!!!!
greatergraces@yahoo.com  
#3 Posted : Thursday, December 30, 2010 9:38:09 PM(UTC)
Quote
greatergraces@yahoo.com

Rank: Member

Groups: Registered
Joined: 11/30/2010(UTC)
Posts: 7

Originally Posted by: denman Go to Quoted Post
Here are your parts
Replacement parts for WHIRLPOOL WED6200SW1 29``ELECTRIC DRYER | AppliancePartsPros.com

This should help with the repair
https://secured.whirlpoo...5435db/$FILE/8178584.pdf

You will see a thermal fuse (Item 7 in Section 3 of the parts).
This is a likely culprit.

Unplug the unit and check the fuse with a meter should be 0 ohms.

Jiggery Pokery method is.
Unplug the unit.
Remove both wires from the fuse, short them together and tape them up so they will not short to the frame.
Plug the unit in and give it a try.

If blown, replace the fuse ASAP as it is a critical safety device re: prevents lint fires which can turn into house fires.

Also clean/check your vent system and the blower as these are the most common causes of it blowing.

This is GREAT HELP thanks alot
greatergraces@yahoo.com  
#4 Posted : Thursday, December 30, 2010 9:50:13 PM(UTC)
Quote
greatergraces@yahoo.com

Rank: Member

Groups: Registered
Joined: 11/30/2010(UTC)
Posts: 7

:)
greater 324903 wrote:
This is GREAT HELP thanks alot

:rolleyes: we took out thremol fuse ,used dryer have been watching closly,it is getting to hot ,would thremol fuse cause this.or do i need to order thermol fuse and something else?dryer is about 15 months old.
denman  
#5 Posted : Friday, December 31, 2010 3:55:50 AM(UTC)
Quote
denman

Rank: Advanced Member

Groups: Senior Expert
Joined: 2/29/2008(UTC)
Posts: 19,638

Thanks: 1 times
Was thanked: 11 time(s) in 11 post(s)
[COLOR="Blue"]we took out thremol fuse ,used dryer have been watching closly,it is getting to hot ,would thremol fuse cause this.[/COLOR]
Not it will not cause overheating.
The overheating probably blew the fuse.
[COLOR="Blue"]
or do i need to order thermol fuse and something else?dryer is about 15 months old.[/COLOR]
[COLOR="Red"]Do not run this unit without a fuse in it !!!![/COLOR]
Shorting it out is only for testing purposes.
Running without it could cause a fire and end up burning down your house.

Have you checked/cleaned your vent system.

Check /clean the blower wheel.
Check the exhaust thermistor resistance.
Check that the seals in the unit are OK. What can happen is that if a seal is shot the unit sucks in room air and then the thermistor sees this as a cooler temperature and runs hot.


Check the heating coil.
Unplug the unit and both wires to the coil.
Check it with a meter, should be around 10 ohms.
Then check from each side of the coil to the case/frame, both should be infinite ohms (open). If not the coil may have sagged or broken and is touching the case. This can cause it to run on high and the thermostats cannot regulate it or the hi-limit thermostat regulates it but it is always on high heat.

If the above are OK then odds are that the control board is shot.
THIS FORUM IS DEAD!!!!!!!
Quick Reply Show Quick Reply
Users browsing this topic
New Topic Post Reply
Forum Jump  
You can post new topics in this forum.
You can reply to topics in this forum.
You can delete your posts in this forum.
You can edit your posts in this forum.
You cannot create polls in this forum.
You can vote in polls in this forum.