|
|||
| Register | FAQ's | New Posts | Today's Posts | Extras |
| » Pots and Pans Light blinking |
|
|
By reading any content on this site you agree to AppliancePartsPros.com, Inc. disclaimer and Terms of Use. |
|
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
|
|||
|
Model Number: 665? Brand: Kenmore Age: 5 - 10 years
Recently, a visitor stumbled onto the open door on our dishwasher (Kenmore Ultrawash). Since then, the door has been hard to open at times. Yesterday, I pulled the unit out from the cabinet some to look at the hinges. I tweaked them slightly to aleviate the binding problem. Now, when we latch the door, the display comes on as normal-70 on the large display and the light above the miser button on. After about 5 seconds, the 70 turns off, and the miser light starts blinking. If I press any buttons, the pots and pans light starts blinking, and that continues until I open the door, press the cancel button or cut the power. If I press the cancel button twice, the drain pump starts and runs for a minute or 2. I think the unit is level. Any suggestions?
Artie Ads By Google Related Models |
|
See inside of your appliance - diagrams and part photos for virtually every model. powered by AppliancePartsPros.com |
|
||||
|
Hi Artie,
In order to provide the most accurate advise I need the complete model number of the dishwasher. Gene.
__________________
Appliance Repair Expert in Orange County, California. Order Appliance Parts with 365-Day Hassle Free Return Policy - AppliancePartsPros.com |
|
||||
|
Artie,
It suppose to be 7 to 8 more digits after "665". If they are missing I probably could not help you as much as I would like. Gene.
__________________
Appliance Repair Expert in Orange County, California. Order Appliance Parts with 365-Day Hassle Free Return Policy - AppliancePartsPros.com |
|
||||
|
Hi Artie,
Remove the inner door panel and the cover. Unplug the ribbon from the power board and clean it, using an eraser. Plug it back, assemble the door and see if it's working. Gene.
__________________
Appliance Repair Expert in Orange County, California. Order Appliance Parts with 365-Day Hassle Free Return Policy - AppliancePartsPros.com |
|
|||
|
Well, I had pulled that plug before, but I looked at it again. It isn't a blade type plug. It is a pin type plug, and I couldn't clean it with an eraser. I looked at the plug and the pin terminal with a bright light and a magnifier and they are clean. Still doing the same thing.
Another person had suggested testing the switches on the latch. They tested good. Is there a reset method on this unit that I should know about? I have turned the power off for more than an hour with no results. Any other ideas? Thanks, Artie |
|
||||
|
Most likely the problem caused by the push button switch.
- The part number for the push button switch is AP3096909 Gene.
__________________
Appliance Repair Expert in Orange County, California. Order Appliance Parts with 365-Day Hassle Free Return Policy - AppliancePartsPros.com |
|
See inside of your appliance - diagrams and part photos for virtually every model. powered by AppliancePartsPros.com |
| Thread Tools | Search this Thread |
| Display Modes | |
|
|
|
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Quiet Partner III, Pots & Pans only cycle that starts | joemess | Dishwasher Repair | 0 | 02-20-2010 11:16 AM |
| Wont run rinse light and cancel light blinking | vershell | Dishwasher Repair | 0 | 07-16-2009 12:45 PM |
| whirlppol DW stops after pots and pans | bowermj | Dishwasher Repair | 1 | 12-22-2008 03:12 AM |
| Pots & Pans light blinks rapidly | bothellboy | Dishwasher Repair | 3 | 02-02-2008 01:10 PM |
| blinking light | wanderingearl | Refrigerator & Freezer Repair | 2 | 12-24-2007 05:42 PM |